Filter Size Chart

Home / Furnace & AC filters / 16x25x1

16x25x1 air filter size

A filter sold as 16x25x1 is not usually 16 by 25 by 1 inches when you measure it. The printed size is the nominal size, used for ordering. The actual frame is typically about 1/4 to 1/2 inch smaller on the face, and thinner than a full inch, so it can slide into the slot.

Nominal size (what you order)
16 × 25 × 1 in
Typical actual size (varies by brand)
About 15.5 × 24.5 × 0.75 in

Filterbuy publishes 15.50 × 24.50 × 0.75 in as its production cut. 3M’s 1-inch MERV 8 data sheet lists 15 11/16 × 24 11/16 × 13/16 in. See the table below.

Nominal size versus actual size

The nominal size is the rounded number printed in large type on the box and on the cardboard frame. Manufacturers cut the filter slightly under that number so it seats in a 16-by-25-by-1-inch slot without binding. Filterbuy describes this as a production choice, not a defect, and notes that the convention is not a published universal standard, which is why actual sizes differ by brand.

If an old filter measures about 15.5 by 24.5 inches and is under 1 inch thick, it is often still a 16x25x1, but you should confirm the nominal size on the frame or measure the slot and compare it with the actual size printed by the brand you are buying.

Published actual dimensions for filters sold as 16x25x1. Figures are from the manufacturers cited, not from independent measurements made for this site.
Brand / document Published actual size Source
Filterbuy 15.50 × 24.50 × 0.75 in Filterbuy 16x25x1 page, production specification
3M HVAC Pro MERV 8 electrostatic filters 15 11/16 × 24 11/16 × 13/16 in
(15.69 × 24.69 × 0.81 in)
3M technical data sheet (PDF)

Some Filtrete consumer packs sold at retail list slightly different actual sizes on the package or listing, so treat the table as a starting point and read the label on the filter in your hand.

How to measure

  1. Read the nominal size printed on the old filter frame first. That is the size to order, such as 16x25x1.
  2. If the print is worn off, measure the old filter’s length, width, and thickness, or measure the slot. The measured size is often a little smaller than the nominal size.
  3. Compare those measurements with the actual size published by the brand you plan to buy. A Filterbuy 16x25x1 is specified at 15.50 × 24.50 × 0.75 inches; a 3M 1-inch MERV 8 in this size is specified at 15 11/16 × 24 11/16 × 13/16 inches.
  4. The filter should slide in snugly. The U.S. EPA says to make sure the filter fits without bending or crushing it, so air does not leak around the edges.
  5. Install it with the arrows on the frame pointing in the direction of airflow, toward the equipment, as Filterbuy instructs.

Compatible systems

A 16x25x1 is a 1-inch pleated filter used in residential forced-air systems. Filtrete’s product pages for 1-inch filters say they can be used in a furnace, air conditioner, or HVAC system. Filterbuy describes furnace, AC, and HVAC filter sizes as the same measurement when one blower and one duct system share a filter slot.

A 16x25x1 is not a substitute for a deeper filter, such as a 16x25x4, that belongs in a media cabinet. Window and wall air conditioners usually use a different kind of filter. If the slot is clearly thicker than one inch, order the depth that matches the cabinet, not a 1-inch filter packed with spacers.

MERV 8, 11, and 13

MERV, or Minimum Efficiency Reporting Value, is a rating from ASHRAE Standard 52.2. The U.S. EPA explains that it reports how well a filter captures particles between 0.3 and 10 microns, and that a higher MERV means higher capture efficiency for the particle sizes in the test. Higher ratings can also add resistance to airflow, so the filter has to be compatible with the system fan and the filter slot.

Average capture efficiency by particle size, from the U.S. EPA’s MERV rating table (based on the ASHRAE 52.2 method).
Rating 0.3–1.0 µm 1.0–3.0 µm 3.0–10.0 µm Who it typically suits, for fit and use
MERV 8 Not specified at this tier At least 20% At least 70% A common 1-inch choice for everyday dust and lint, with generally lower resistance than higher ratings.
MERV 11 At least 20% At least 65% At least 85% A middle step when you want tighter filtration than MERV 8. Confirm the system still moves air well after you install it.
MERV 13 At least 50% At least 85% At least 90% The EPA recommends a filter rated at least MERV 13, or as high as the system fan and filter slot can accommodate. Most systems can use MERV 13 if the filter is replaced often; an HVAC technician can confirm compatibility.

This page does not make health, allergy, or medical claims. If you are unsure whether a higher MERV will restrict airflow in your equipment, check the system manual or ask a licensed technician. The figures above are the EPA’s published minimums for each rating, not test results for a specific brand.

How often to replace a 1-inch 16x25x1

Follow the filter maker and your HVAC manual first. For 1-inch pleated filters, two manufacturers give this guidance:

The EPA’s Guide to Air Cleaners in the Home says to replace filters according to the manufacturer’s recommendations, and that manufacturers typically recommend replacement every 60 to 90 days. A clogged filter can add resistance, which is one reason those schedules exist. This is maintenance guidance, not a medical recommendation.

Where to buy

As an Amazon Associate I earn from qualifying purchases.

These buttons go to official product pages and do not include an affiliate tag. After the site is enrolled in the Filterbuy Partner program and Amazon Associates, the destinations can be replaced with tagged links. The tokens FILTERBUY_AFFILIATE_URL and AMAZON_ASSOCIATE_TAG mark where those tagged URLs should go. No commission is earned from the current links.

Shop 16x25x1 at Filterbuy Search 16x25x1 filters on Amazon

These are official, untagged links — Filterbuy’s 16x25x1 page and an Amazon search with no associate tag. A cited Filtrete / 3M product page is listed in the sources below. Prices are omitted because they change.

Frequently asked questions

My old filter measures about 15.5 by 24.5 inches. Is that a 16x25x1?
Often yes. Filterbuy’s 16x25x1 is specified at 15.50 × 24.50 × 0.75 inches. Other brands run a little closer to 16 by 25, such as 3M’s 15 11/16 by 24 11/16 by 13/16 inches. Check the nominal size printed on the frame, or compare your measurements with the brand you are buying.
Can I put a 16x25x4 in a 16x25x1 slot?
No. The first two numbers may match, but the depth does not. A 4-inch filter belongs in a 4-inch media cabinet, not in a 1-inch slot.
Which way does the arrow face?
Toward the furnace, air handler, or other equipment, in the direction of airflow, as printed on the frame.
Do I need a different size for the air conditioner than for the furnace?
Usually not, when both use the same forced-air system and the same slot. Confirm by reading the filter that is already in that slot.

Sources